| Digitax DCC Model Railroad Accessories | |||
|---|---|---|---|
| Digitrax Gray Terminal Plug |
Please correct the following error: |
Booster Terminal Plug | Add To Cart |
| Digitrax Card Edge Connector 44 Pos 3pk |
Please correct the following error: |
Edge Connector | Add To Cart |
| Digitrax Decoder Installation Wire |
Please correct the following error: |
30 awg | Add To Cart |
| Digitrax LT1 Decoder & Loco Net Tester |
Please correct the following error: |
Decoder Tester Loco Net Tester |
Add To Cart |
| Digitrax LT5 Tester for BDL16 Series |
Please correct the following error: |
For BDL16 Series | Add To Cart |
| Digitrax MS100 Computer Interface |
Please correct the following error: |
Loco Net to RS232 | Add To Cart |
| Digitrax Command Control Book |
Please correct the following error: |
The Book ! | Add To Cart |
| Digitrax RD2 Remote Sensing Diode |
Please correct the following error: |
For BDL16 | Add To Cart |
| Digitrax DM1 DC Motor Adapter |
Please correct the following error: |
For DS54 | Add To Cart |
| Digitrax DHAT Plug N Play Harness |
Please correct the following error: |
Athearn Loco | Add To Cart |
| Digitrax DHDP Decoder Dummy Plugs |
Please correct the following error: |
5 Per Pack | Add To Cart |
| Digitrax DHWH Wire Harness |
Please correct the following error: |
5 Per Pack | Add To Cart |
| Digitrax DHWHP Med Wire Harness |
Please correct the following error: |
3.25 " Leads | Add To Cart |
| Digitrax DHWHPS Med Wire Harness |
Please correct the following error: |
1.5" Leads | Add To Cart |
Digitrax Booster Terminal Plug - Gray replacement for lost or damaged plugs on DB150, DB200+, DCS100 and DCS200
Digitrax Edge Connector - 3 pack for use with PM4 series boards, BDL16 series boards and SE8 Series boards
Digitrax Decoder Wire - For decoders, lighting and signaling. 90ft of 30awg stranded wire. 90ft consists of 10ft each of 9 colors.
Digitrax LT1 Tester - For decoders and LocoNet cables. Included with all Digitrax Starter Sets, the LT1 consists of a harness with 6 conductor telco type cable and a male plug, as well as a tester with a female 6 conductor jack and protection resistor.
Digitrax LT5 Tester - For BDL16 Series
Digitrax MS100 RS-232 Computer Interface- The Digitrax MS100 Computer Interface is designed to let a computer with a IBM compatible COM port or RS232 communication interface monitor Digitrax LocoNet. Application software running in the computer can then interpret the activity on the LocoNet and report back to the user via the computer screen. The MS100 is a signal level translator between LocoNet and a 25 pin DB25 style RS232 port.
Digitrax DCC Book - The Big Book Of DCC
Digitrax RD2 Remote Sensing Diode - For BDL16 and BDL162. Remote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the BDL16 and remotely located track sections.
Digitrax DM-1 DC Motor Adapter - The DM-1 is an inline adapter designed to modify any DS54 output to provide the bi-polar drive current needed to run reversible DC motors, solenoid switches (such as KATO and LGB Turnouts), lamps and other similar devices that draw up to .5 amps.
Just plug the DM-1 into any DS54 output and the DM-1 socket will provide a bi-polar drive rated at 500ma continuous and 1 amp surge.
Digitrax DHAT 9 Pin Harness for Athearn Loco - Digitrax 9 pin harness with no-solder connections for Athearn Standard Locomotive
Digitrax DHDP Dummy Plugs 5 Pack - Digitrax Dummy Plugs for analog operation of Digitrax Easy Connect harnesses. 5 pack
Digitrax DHWH 9 Pin to Wire Harness 5 Pack - Digitrax 9 pin to bare wire harness. 5 pack.
Digitrax DHWHP 9 Pin to DCC Medium Plug Long Harness - Digitrax 9 pin to DCC medium plug long harness. 3 inch wire
Digitrax DHWHPS 9 Pin to DCC medium Plug Short Harness - Digitrax 9 pin to DCC medium play short harness. 1 inch wire